Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Granada Hills
If your driveway gate is sagging, binding, or refusing to open, the fix usually comes down to a few specific parts: hinges, posts, rails, rollers, or a cracked weld. In Granada Hills, gate repair costs typically run $180-$480 depending on what failed, and most hinge and latch replacements are done same-day. At Gatewood Fence & Gate, we weld on site so your gate never leaves your driveway. Call (818) 873-5061 and you’ll talk to a live person, not a menu. Hal Gatewood has been at this since 2001, and he still answers the phone himself.
Granada Hills gates fail differently than gates in Sherman Oaks or Chatsworth. The soil shifts, the heat dries everything out, and the Santa Ana winds hammer the foothill streets north of Rinaldi harder than anywhere else in the Valley. We know what that does to a hinge post. We know which welds crack first on a mid-90s Viking operator. And we know the difference between a gate that needs a new part and one that just needs the old part re-set correctly. That knowledge means you don’t pay for work that won’t last.
Why Gatewood Fence & Gate Is Granada Hills’s Preferred Gate Parts & Welding Company
We’re the company people call after the other guy already tried. Granada Hills homeowners show us gates with brand-new hinges bolted to leaning posts, fresh welds laid over cracked ones, and operator boards replaced when the real problem was a corroded loop detector in the driveway. A gate sags in the hinge post, not in the middle. Fix the panel without the post and you’ll fix it twice. Hal’s crew has been correcting those mistakes in Granada Hills long enough to know where they start.
Every job from Gatewood Fence & Gate carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back – no runaround, no fine print. We’re locally owned and owner-operated with a published address and license number anyone can look up. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is. Calls are answered by a live person 24/7, and the person who shows up is background-checked and wears a uniform. We service nine major gate brands including BFT, Linear, Viking, and Ghost Controls, so the parts we install are the parts actually spec’d for your operator.
Our Gate Parts & Welding Services in Granada Hills
Hinge Replacement
Most swing gates in Granada Hills wear out at the hinge before anywhere else. The wide post-quake lots and long driveway approaches mean bigger, heavier gates, and those gates lean hard on their hinge hardware every time the Santa Ana winds push through the foothills. We replace worn hinge pins, barrel hinges, and weld-on strap hinges with stainless or galvanised steel that actually holds up to Valley heat and dust. A typical hinge replacement in Granada Hills runs $180-$340 depending on gate weight and whether the post needs re-shimming at the same time.
Post Replacement
Here’s what we see constantly north of Rinaldi: a gate post that looks plumb from the driveway but is actually set in a cracked or heaved footing. Between the quake-era retrofits of the mid-90s and decades of wide temperature swings, the concrete around those posts gives way. The post leans. The gate binds at the latch. No new hinge fixes that. We cut the old post out, core-drill a deeper footing, set a thicker-wall steel post, and weld it in properly. Post replacement in Granada Hills typically runs $450-$900 depending on depth, access, and whether the operator mount needs re-fabricating.
Rail Repair
Welded steel gates take a beating in this climate. The expansion and contraction from 40-degree winter mornings to 110-degree August afternoons stress every weld on the frame. When a bottom rail or picket weld cracks, the gate starts to rack and the operator strains. We grind out the old cracked weld, bevel the joint, and lay a proper multi-pass weld with the right rod. Repairing a cracked gate rail in Granada Hills costs $120-$280 for most residential gates. We do it on site, in your driveway, without removing the gate.
Custom Welding
Sometimes the gate can’t just be repaired. A post-quake retrofit gate with original mid-90s hardware might need new mounting plates, a re-fabricated hinge bracket, or an entirely new frame section to hold modern operator arms. Hal welds it in the driveway. We don’t haul your gate to a shop across the Valley and bring it back two weeks later. Custom welding projects in Granada Hills range from $200 for a bracket re-fabrication to $1,500-$2,800 when we’re rebuilding a section of a large foothill driveway gate. The estimate is always written, and the price is always agreed before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Granada Hills
We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Granada Hills specifically, we see a lot of original mid-1990s Viking and Linear operators on the post-quake rebuild homes. Those units have particular failure patterns – corroded motor housings, worn limit switches, failed loop detectors – and we stock the replacement parts for them locally. When your BFT or Ghost Controls opener needs a control board or a set of photo eyes, we can usually have it on the truck the same day rather than waiting on a warehouse drop-ship. Call (818) 873-5061 and tell us what brand is on your opener. We’ll tell you honestly whether it’s worth repairing or whether you’re better off replacing the unit.
Common Gate Parts & Welding Problems We See in Granada Hills Homes
- Leaning hinge posts with no visible rust or damage. This is the post-quake footing problem. The post looks fine, the concrete pad looks fine, but the footing underneath has cracked and the post is slowly tilting. The gate binds at the latch side and the operator labors. Until the post is re-set, no hinge work will hold.
- Mid-90s Viking and Linear operators that fail in heat or wind. Santa Ana wind-driven dust gets into the motor housing and the loop detector. The heat dries out lubrication and cooks the circuit board. The gate itself may still be mechanically sound. The opener is just old and corroded.
- Cracked hinge welds that keep re-cracking. When the original hinge was welded with mild steel rod instead of 7018, the heat-affected zone cracks again within a year. We see this on older welded steel swing gates throughout Granada Hills. The fix is grinding out the old weld, re-setting the post if needed, and laying a proper weld that won’t fail next summer.
- Slide gates that rack and bind on heaved concrete. Properties along the foothill streets north of Rinaldi often have gates set on sloped or terraced entries. The concrete under the gate track shifts. The rollers wear unevenly. The gate starts to drag. New rollers help, but only if the track is re-leveled first.
Pricing for Gate Parts & Welding in Granada Hills, CA
Here’s what you can expect to pay for common Gate Parts & Welding work in Granada Hills:
- Hinge replacement (single swing gate): $180-$340
- Hinge replacement (double gate or heavy foothill gate): $280-$480
- Post replacement with new footing and weld: $450-$900
- Single rail crack repair (grind, bevel, multi-pass weld): $120-$280
- Custom bracket or mount re-fabrication: $200-$500
- Full section rebuild on large driveway gate: $1,500-$2,800
The price depends on the gate’s size, the condition of the post footings, and whether the operator needs any work at the same time. What it doesn’t depend on is our mood that day. The price Hal quotes you is the price on the invoice, and it’s agreed in writing before any work starts. We offer no trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Estimates are free. Call (818) 873-5061.
We Also Serve Cities Near Granada Hills
Our team handles Gate Parts & Welding work throughout the north Valley. We’re regularly in San Fernando, Northridge, Sylmar, and Panorama City, and because dispatch and scheduling are coordinated from our Los Angeles office, we can route a Granada Hills job quickly. See more about our local coverage at Gate Parts & Welding in Granada Hills or just call and ask. If you’re within the county, there’s no trip charge.
Serving Granada Hills, CA - Our Local Coverage Area
We’re based in the Granada Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Granada Hills
Because the footing under the post has failed, not the post itself. The 1994 Northridge earthquake and the post-quake rebuild boom left many Granada Hills gates set in shallow, unreinforced concrete. Decades of Valley heat expansion and soil contraction crack that concrete and shift the footing. The post tilts, the gate binds at the latch, and no new hinge will fix it. The post has to be core-drilled out, re-set deeper, and re-welded. Call (818) 873-5061 for a free look – if the post is still sound, we’ll tell you that too.
Two causes usually work together. First, Santa Ana wind-driven dust coats the loop detector and the limit switches, causing intermittent faults when the wind picks up. Second, the motor housing on a 30-year-old Viking operator is often corroded enough that wind-driven debris finds its way inside and causes short circuits. The heat you mentioned actually helps by drying out moisture. The wind is what brings the dust and debris. We can clean and service the detector, replace the limit switches, and tell you honestly whether the operator is worth saving. Call (818) 873-5061.
Yes. We weld on site. Hal’s truck carries a full welding rig, and we do nearly all residential gate welding in the driveway without removing the gate. For a cracked rail, we grind out the old weld, bevel the joint, and lay a proper multi-pass weld right where the gate hangs. We just need enough clearance to access the joint safely. On steep foothill driveways, that sometimes means setting up on the slope, but we do it routinely. Call (818) 873-5061 to describe the crack and we’ll tell you what it’ll take.
Galvanised steel is zinc-coated and resists rust for 20-30 years in Valley conditions. Painted steel is cheaper up front but the paint scratches during installation, the scratch rusts, and the post starts corroding at ground level within a few seasons. For any post set in concrete in Granada Hills, we recommend galvanised or powder-coated steel. The difference in materials cost is small compared to the labor of digging out the old post. We’ll quote both if you want, but we’ll be honest about which one makes sense for your gate. Call (818) 873-5061.
Yes. The loop detector is the part buried in the driveway that senses your car and tells the operator to open. On Granada Hills lots where the driveway pad has shifted or cracked from soil movement, the loop wire breaks. The operator still runs fine when you use the remote or keypad, but it won’t respond to a car pulling up. A new loop detector for an older Linear gate typically runs $200-$400 installed. We test the loop before touching the operator so you don’t pay for a new board you didn’t need. Call (818) 873-5061 and we’ll walk through the symptoms with you.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Granada Hills since 2001.