Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Beverly Hills
A gate motor replacement in Beverly Hills typically runs $1,400-$4,800 installed, and a same-week appointment is realistic for most repair calls. The bigger variable isn’t labor: it’s whether your operator is compatible with the custom gate it’s driving, and whether the wiring passes Beverly Hills building inspection. That’s where we come in. Hal Gatewood has been fixing and installing gate operators since 2001, and he answers the phone himself at (818) 873-5061.
Beverly Hills isn’t like working in West Hollywood or Sherman Oaks. The gates here are heavier, the pillars are older, and the building department answers to its own codebook. We know all three. When we show up on Rexford Drive or up in the hills off Coldwater Canyon, we already know what the inspector is going to ask before we unload the truck.
Why Gatewood Fence & Gate Is Beverly Hills’s Preferred Gate Motor & Opener Company
We’re the outfit that fixes the operator when two other companies said you needed a new gate. Hal welds on site, in your driveway, not back at some warehouse. If a hinge post is pulling loose on a 1930s Spanish Colonial on Canon Drive, we repair the post and remount the motor. That’s the difference between a gate that opens and closes for ten years, and one that fails again next autumn.
Beverly Hills homeowners call us because the name on the invoice matches the name on the shop. Hal Gatewood’s address is published, his license number is on file, and every job carries the 90-Day Done Right Promise in writing. One call brings him back. No runaround, no “that’s a different warranty department.” You get the person who did the work.
Every call is answered by a live person, 24/7. Somebody in the office, not a voicemail tree. If your intercom stops triggering the gate at 6 a.m. before your housekeeper arrives, you call us and a human picks up.
Our Gate Motor & Opener Services in Beverly Hills
Motor Installation
We install operators sized for real Beverly Hills gates, not the light aluminum tube jobs you see in the Valley. On a custom wrought iron swing gate on Roxbury Drive, that means an operator with real torque and a heavy-duty arm. We set the opening and closing force correctly, not just until it “sounds okay.” We also surface wire along original stone or brick pillars rather than coring through them, because a 90-year-old masonry pier on a Beverly Hills Flats property is not a conduit chase.
Motor Repair
If your operator is grinding, hesitating, or refusing to close fully, we diagnose the actual failure before we touch anything. Often on Beverly Hills estates it’s a worn gearbox from fighting a sagging hinge post, or a limit switch burned out from years of Santa Ana wind loading. We repair the motor and the cause. A motor swap that ignores the sagging post fixes nothing for more than a few months, and we won’t do that to you.
Linear Motor
Linear operators are what we install on long driveway slide gates up in the hills above Sunset. These units run on a screw or rack drive, and Beverly Hills grade makes them work harder than they would on flat lots. We install them with proper supporting wheels and rollers so the operator isn’t dragging the whole gate. On a cantilever slide gate off Benedict Canyon, a properly set linear motor lasts years. A sloppy one strips in a season.
Slide Motor
Cantilever slide gates are common in the Beverly Hills hills, and they carry a lot of weight when the grade pitches. We set the operator so the gate carries its own load, not the motor. That means correct counterweight, solid rollers, and a motor sized for the actual gate mass. We also harden the photo-eye wiring and seal sensor housings against the sun exposure that eats cheap lenses here faster than in Santa Monica.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Beverly Hills
We fix and install FAAC, BFT, LiftMaster, Viking, and Linear operators, along with several others. Beverly Hills gates run commercial-grade hardware because the gates demand it. We keep common FAAC and Viking parts on the truck, and that means fewer return trips for customers near Doheny Road or up in Trousdale Estates. If your operator is still under manufacturer warranty, we handle the paperwork.
Common Gate Motor & Opener Problems We See in Beverly Hills Homes
- Santa Ana wind damage to limit switches. The fall winds hit a heavy solid-panel gate broadside, and the operator’s limit switch takes the brunt. You hear the motor running but the gate doesn’t stop where it should, or it slams at the end of travel. We replace and recalibrate the switch, and on Beverly Hills hillside properties we recommend an annual pre-season check.
- UV-degraded photo-eye lenses and wiring. South-facing gates on Beverly Hills properties get hammered by Southern California sun. The clear plastic lens on the photo-eye fogs and cracks, and the wiring jacket gets brittle. Your gate reverses for no reason, or refuses to close at all. We replace with UV-stabilized sensors and conduit-sealed wiring.
- Gearbox wear from sagging hinge posts. On older Flats estates, the original iron hinge post has pulled just enough that the gate leaf drags or hangs low on the latch side. The operator pushes against that extra resistance every cycle, and the gearbox grinds down. We repair the post, remount the gate level, and then the new motor runs against a balanced gate instead of a weight-lifting contest.
- Intercom integration failures. Beverly Hills homes with Crestron or Control4 systems often lose the phone-to-gate link after a system update, or the intercom works but the gate won’t trigger. We trace the dry contact wiring and integrate the operator with your automation platform so the gate answers the same commands as everything else on the property.
Pricing for Gate Motor & Opener in Beverly Hills, CA
A standard motor replacement on an existing swing gate in Beverly Hills runs $1,400-$3,200. Slide gate operators run $2,200-$4,800 installed. Linear motor replacements for long driveway gates up in the hills typically land around $2,800-$4,200. Intercom integration adds $300-$900 depending on your system and how much wiring we’re pulling. These are honest numbers for Beverly Hills work, not a teaser rate that doubles when the invoice comes.
What moves the number: gate weight and length, pillar condition, whether we’re surface-running conduit along original masonry, and whether the operator needs to tie into a smart-home system. We quote the job before we start, in writing, and that number doesn’t change when we’re packed up and heading out. Call (818) 873-5061 for a free estimate. There’s no trip charge inside the county, and seniors and veterans get 10% off, permanently. We also offer $40 off any repair over $200 and a free second opinion on any written estimate.
We Also Serve Cities Near Beverly Hills
While this page is about Beverly Hills, our crews regularly work in West Hollywood, Studio City, Sherman Oaks, and Santa Monica. We coordinate from our Los Angeles office and dispatch locally. For more on how we approach this work across the region, see our Gate Motor & Opener service page. For Beverly Hills specifics, you’re already on the right page.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Beverly Hills
Yes, we handle the Beverly Hills permit process when the work requires it. Straight motor swaps on existing permitted gates usually don’t need a permit, but any new electrical run, new operator location, or structural work on pillars does. Beverly Hills is its own municipality, separate from Los Angeles, so we file with the Beverly Hills building department and schedule inspections. We won’t tell you a permit isn’t needed when the city says otherwise. Call us and we’ll tell you whether your job needs a permit before you spend anything.
Yes, we install solar-powered gate openers on Beverly Hills properties where trenching power isn’t practical or would damage original landscaping or hardscape. Solar systems work well for single-family swing gates and moderate-use slide gates, but heavy wrought iron gates cycled many times daily often outrun battery capacity, especially during shorter winter days. We’ll size the panel and battery to your actual usage, not a generic spec sheet. Call us and we’ll walk the gate with you.
For a heavy wrought iron swing gate on a Flats property, we typically recommend a commercial-rated FAAC or BFT operator with an articulated arm, sized for the full gate leaf weight and width. The original limestone pillars on those 1920s and 1930s estates can’t take a surface-mounted ram operator without cracking, so we use underground or articulated arm options that preserve the masonry. We’ll match the operator to the actual weight of your gate, not a catalog guess. Call for an exact recommendation.
We recommend an annual service for Beverly Hills gate operators, timed before the fall Santa Ana season. The winds put heavy lateral load on solid-panel gates, and that stress shows up in limit switch drift, hinge wear, and gearbox strain. An annual check catches a failing part before the wind season finds it. It’s a lot cheaper to replace a $90 limit switch in August than a $2,400 operator in November. Schedule a service call.
No, replacing the motor will not fix a sagging hinge post. The sag means the post has moved or the hinge has worn, and a new motor will just grind against the same resistance until it fails too. We fix the post first, rehang the gate level, and then install a motor that isn’t fighting a losing battle. That’s the repair-first approach Hal has used since 2001. Call us and we’ll show you exactly where the gate is failing before we sell you anything.
If your Beverly Hills gate motor is dead, noisy, or just unreliable, call Hal at (818) 873-5061. You’ll talk to a live person, get a straight answer, and get a written quote before any work starts. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Beverly Hills since 2001.