Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Encino
Gate installation in Encino runs $1,800-$12,000 depending on the gate style, operator choice, and whether we’re working with new post footings or existing hardware. Most driveway gate installations take one to three days on site, and we quote the full job before any work begins. Hal Gatewood has been at this since 2001, and the crew that shows up at your Encino home is the same crew whose name is on the invoice. Call (818) 873-5061 for a free estimate on your Encino Gate Access Control project and we’ll walk the gate line with you.
Why Gatewood Fence & Gate Is Encino’s Preferred Gate Installation Company
Encino is a specific kind of market. North of Ventura Blvd, we’re not installing lightweight aluminum driveway gates on flat suburban lots. We’re working with heavy custom wrought-iron swing gates, long slide tracks on hillside driveways, and operator housings that have been baking in 105-degree Valley heat for 30 years. A company that mostly installs in new tracts doesn’t know what happens to a gate post in adobe-heavy Encino Hills soil, or why a slide gate on a Hayvenhurst Ave slope binds differently than one on flat ground. We know because we’ve pulled failed posts and burned-out motors out of Encino driveways for over two decades.
Our promise is simple and written on every invoice: the 90-Day Done Right Promise. If it’s not done right, one call brings Hal back. No runaround. No arguing. We also answer the phone with a live person 24 hours a day, seven days a week. Not a voicemail. Not a call center in another state. A person who can look up your address on a map and tell you when we’ll roll onto Amestoy Ave or Balboa Blvd.
Hal’s crew has installed gates on estates off Royal Oak Road, replaced slide gates along Ventura Blvd properties, and re-hung swing gates in the ranch-home streets south of the Blvd. The work varies, but the standard doesn’t. We’re background-checked, uniformed, and certified to work on LiftMaster, FAAC, BFT, and Linear equipment. And if you want to verify who we are, drive to the shop and look Hal in the eye. The address is published. The name is on the door.
Our Gate Installation Services in Encino
Driveway Gate Installation
Most Encino driveway gates north of Ventura Blvd are wide, heavy, and built to match an estate home’s architecture. That means custom steel or wood-and-iron construction rather than a stock panel dropped into place. We measure the driveway width, grade, and gate swing clearance on site, then build the gate to fit that exact opening. A double driveway gate in Encino typically runs $4,500-$9,800 installed, including new powder-coated steel frames and operator-ready hinge posts.
Pedestrian Gate Installation
Pedestrian gates in Encino are often paired with a driveway gate, especially on hillside estates where the walk gate sits on a sloped path or retains a low wall. We install standalone pedestrian gates from $1,200-$3,200 depending on width, material, and whether you want a matching keypad or intercom tie-in to the main entry. A sagging pedestrian gate is usually a failed post or a hinge pulling out of stucco, and that’s where we start.
Sliding Gate Installation
Sliding gates are common on Encino properties where the driveway slopes down toward the house and there’s no room for a gate to swing inward or outward. We install cantilever and track-guided slide gates, and on Encino hillside lots we account for debris that Santa Ana winds push into the track channel. A custom steel slide gate in Encino typically costs $3,800-$8,500 installed, with the operator and rack included. If your driveway is on a grade, we check the wheel load and track level before anything gets welded. Our Gate Parts & Welding - Encino team builds these to last.
Swing Gate Installation
Swing gates are the signature of Encino’s estate neighborhoods. Double wrought-iron swing gates on Amestoy Ave, Royal Oak Road, and Rancho St often weigh 400-800 pounds per leaf, and they put enormous force through the hinge post. We set deep post footings, use heavy-wall posts, and install operators rated for the actual gate weight, not the optimistic spec on a box. A double swing gate with automation in Encino runs $5,500-$12,000 depending on size and ornamental work. We also do single swing gates for ranch homes south of the Blvd, starting around $2,200.
If you already have a gate and want to know whether your existing posts can carry a new one, call us. We’ll come out, look at the post bases, and tell you what you need. That’s a free estimate, no obligation. This is part of our broader Gate Installation work across Los Angeles County, but the Encino side of it has its own character.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Encino
We install and service LiftMaster, FAAC, and Linear operators on a regular basis, and we carry the common boards, photo eyes, and receiver parts those brands need so you’re not waiting a week for a part to ship. For Encino homes still running an old Apollo or first-gen Linear unit, we’ll tell you honestly whether it’s worth repairing or whether the parts are gone and a replacement operator is the only path. A new LiftMaster LA400PKGU or FAAC 400 series operator installed on an Encino gate runs $1,200-$2,400 depending on power needs and safety accessory integration.
Common Gate Installation Problems We See in Encino Homes
- Burned-out operator motors and control boards from extreme interior heat. Encino regularly hits 100-110°F in summer, often 15-20 degrees hotter than coastal LA. That heat cooks motor windings and degrades circuit boards far sooner than manufacturer service life ratings suggest, which is why we specify operators rated for continuous high-ambient duty on any Encino estate install.
- Santa Ana wind debris jamming slide-gate track channels. Fall and early winter winds funnel through the Valley and push leaves, twigs, and plastic bags into slide gate tracks. We install debris shields and elevated track systems on the worst-exposed properties, and we recommend a track inspection every fall.
- Legacy Apollo and Linear operators from the 1980s-90s that are now parts-obsolete. A huge share of Encino’s hillside estates still run on first- and second-generation units that can’t get replacement boards anymore. What starts as a service call often becomes a full operator replacement on installation day.
- Sagging hinge posts on heavy ornamental gates. The combination of heavy 1980s-era wrought-iron panels, expansive clay soil, and decades of Valley heat cycles pulls hinge posts out of true. We set new footings and re-weld gate frames so the gate hangs square and runs silent.
Pricing for Gate Installation in Encino, CA
Here’s what we’re seeing on current Encino jobs:
- Pedestrian gate: $1,200-$3,200
- Single swing gate with operator: $2,200-$5,500
- Double swing gate with operator: $5,500-$12,000
- Slide gate with operator and track: $3,800-$8,500
- Operator-only replacement on existing gate: $1,200-$2,400
What moves the price in Encino is gate weight, ornamental detailing, post footing depth, and whether we’re matching an existing estate aesthetic. The price we quote is the price you pay. Before any work starts, you get a written number and we don’t change it at the door. We also offer $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (818) 873-5061 for an exact quote. Estimates are free.
We Also Serve Cities Near Encino
If you’re just outside Encino, we regularly install gates in Encino and the surrounding neighborhoods including Tarzana, Reseda, Sherman Oaks, and Van Nuys. The gate challenges are similar, the heat is the same, and we’re close enough to be there the same day you call.
Serving Encino, CA - Our Local Coverage Area
We’re based in the Encino area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Encino
Encino’s interior Valley heat shortens operator lifespan by 30-50% compared to coastal installations. The 100-110°F summer temperatures bake motor windings, swell and crack control board solder joints, and harden wiring insulation. We specify high-ambient-rated operators, install vented housings where possible, and recommend a thermal inspection every two summers. For an exact operator recommendation for your driveway sun exposure, call (818) 873-5061 and we’ll come look.
In most cases on Encino hillside estates, if your Apollo or Linear operator is from the 1980s or early 90s, the parts are gone and a full operator replacement is the only practical path. If the gate panel and posts are still sound, we can install a new LiftMaster or FAAC operator onto the existing gate, which runs $1,200-$2,400. We’ll check the gate weight, post condition, and wiring first, and tell you what’s actually needed. Call for an honest assessment. We’ll give you a written answer.
Yes. On heavy custom wrought-iron gates, especially in Encino’s hillside and estate neighborhoods, we set new steel-reinforced concrete footings for the hinge posts as standard practice. Encino’s clay-heavy soil expands and contracts aggressively with the Valley’s wet-dry cycles, which is why old posts pull out of true over time. New footings are priced into the installation quote, not added on later.
Santa Ana wind events blow debris into slide gate track channels, which causes the gate to bind, grind, or stall mid-travel. On Encino properties exposed to the prevailing wind path, we install elevated track systems and debris shields, and we run the gate through a full travel test after every install. A track cleaning and adjustment service call is $180-$320 depending on the track length, and you can call us any hour at (818) 873-5061 if a storm has knocked your gate out of true.
Yes. We fabricate custom ornamental panels and rebuild gates to match the original style of an Encino estate home. On one Royal Oak Road property, we replaced a sagging split-wood-and-iron swing gate whose 1990s Linear operator had burned out its control board in the Valley heat. We set new post footings for the hinge posts, installed a LiftMaster LA400PKGU operator with a loop detector and safety photocells, and fabricated a matching ornamental panel so the gate runs silent and true. If you want the gate to look like it belongs to the house, that’s exactly how we build it.
Call Gatewood Fence & Gate for Your Encino Gate Installation
If you live north of Ventura Blvd in Encino Hills or south of the Blvd in the ranch streets, we know your gate. We’ve installed swing gates on Lanai Road, slide gates off Balboa, and double estate gates throughout Encino for over two decades. Hal Gatewood’s name is on the shop and on every invoice, and the 90-Day Done Right Promise is stamped in writing. Call (818) 873-5061 now for a free estimate. A live person answers, day or night, and the estimate you get is the price you’ll pay.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Encino since 2001.