Viking Gate Installation Nationwide | Gatewood Fence & Gate

Viking Gate Installation in Sherman Oaks: What to Know First

Independent Viking gate installation in Sherman Oaks typically runs from $1,400 for a basic single swing gate up to $6,500 or more for a long sliding driveway gate with an operator, and most jobs are completed within two to three days once parts are in hand. We are an independent Viking service provider, not a manufacturer-authorized shop, which means we make the call on what actually needs replacing rather than what a warranty flowchart says. If you own a Viking gate in Sherman Oaks and you need it installed right the first time, call (818) 873-5061. This page is for homeowners who already have a Viking gate, or are considering one, and want the straight version of what installation really involves on Van Nuys Boulevard, in the Encino-adjacent flats, or up in the hills where the wind actually matters.

Call (818) 873-5061

How Viking Products Fail - and How We Fix Them

Viking gates are built heavier than a lot of what shows up in Sherman Oaks driveways, and that weight is both the selling point and the weak spot. Here’s what we see week after week, and what we do about it.

• Viking G-5 and F-1 series: hinge post lean. These are substantial gates, and on Sherman Oaks slopes they put more lateral load on the hinge post than the original installers ever accounted for. The gate sags in the post, not in the middle. We pull the gate, re-set the post in concrete with proper depth for the soil here, and weld the hinge brackets rather than relying on bolts that loosen over time.
• Viking Vikingline and Titan series: undersized post footings. A long Titan sliding gate catches wind like a sail on a Sherman Oaks ridgeline. We routinely find footings poured 18 inches deep where 30-plus is needed for the weight and exposure. We re-pour and re-set, then re-hang the gate so it tracks straight instead of creeping sideways.
• Viking rotary operators with aftermarket gearboxes. The OEM Viking operator is fine, but we see a lot of no-name replacement gearboxes that whine and bind after a season. On a Viking install we check the operator mounting plate and the rack alignment before assuming the motor is at fault. A Viking gate that grinds on a windy Sherman Oaks afternoon is almost always rack alignment, not motor death.
• Viking cantilever gates with rusted roller bolts. Sherman Oaks is not exactly the coast, but morning marine layer plus sprinkler overspray is enough to seize the hardware on a cantilever gate. We replace the roller bolts with stainless and set the gate height so it clears the concrete without dragging. If the gate scraped once, it’s been scraping for months.
• Viking pedestrian gates with welded-in panel warping. Some Viking pedestrian gate models have the top panel welded fully around the frame, and heat expansion in direct Sherman Oaks sun causes a slight bow that makes the latch line up wrong in the evening. We add a stiffener or adjust the latch throw rather than telling you to live with it. A latch that only works at noon is still a broken latch.

Our Viking Gate Installation Process

1. 1
   You call, a person answers. We talk through what Viking gate you have, where it sits, and what it has been doing. If we need to see it, we set a window and we keep it.
2. 2
   We look at the whole system. Posts, hinges, gate weight, operator, photo eyes, safety edges, the run of the track if it’s a slider. On a Viking, the post condition tells us more than the gate panel does. Fix the panel without the post and you’ll fix it twice.
3. 3
   Parts decision, out loud. We tell you what needs replacing and whether OEM Viking parts are worth the wait or if a quality aftermarket component does the same job for less and lasts the same. We do not swap parts that still have life in them.
4. 4
   The work happens in your driveway. We weld on site, hang the gate ourselves, and set the operator to match the gate weight rather than guessing at a dial. No hauling your gate off to some shop across the Valley.
5. 5
   We run the cycle a lot. A Viking gate that closes perfectly twice and slams on the third is not done. We test under load, with wind, with the safety edges, with the auto-reverse, until it behaves consistently. Show me the gate closing on its own and I’ll show you where it’s failing, so we keep testing until there’s nothing to show.
6. 6
   You get the 90-Day Done Right Promise in writing. Stamp on the invoice, plain language. If it isn’t done right, one call brings us back. No runaround.

What Viking Gate Installation Costs in Sherman Oaks

Straight numbers from the jobs we’ve done in this area, so you have a real baseline.

What moves the price is post condition, gate weight, and whether the operator is staying or going. Sherman Oaks hills sometimes mean hand-carrying everything up a slope, which adds labor. We quote the job before we start, and that quote doesn’t change at the door. Call (818) 873-5061 for a free estimate on your Viking gate installation. No trip charge inside the county, and $40 off any repair over $200 if the job turns into a repair instead of an install.

Why Sherman Oaks Homeowners Call Gatewood Fence & Gate for Viking Work

Hal Gatewood has been fixing gates in Sherman Oaks since 2001, and most of his customers are within a few miles of the Ventura Boulevard stretch he’s driven every single workday for over two decades. Hal picked up the trade at Los Angeles Valley College over in Valley Glen, where he took vocational welding and metal fabrication courses after spending his twenties doing general handyman work and realizing he wanted something more specific under his belt. The name is on the shop, and the shop is down the road - that is the oldest accountability there is. We answer the phone with a live person around the clock, and the person who shows up is the person who takes the call. We also service the other big names around Sherman Oaks driveways: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. If you have a Viking now and a DoorKing on the other side of the property, one call covers both. Every job carries the 90-Day Done Right Promise in writing, and we’ve been doing that since before it was a marketing thing.

FAQs