Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterElite Gate Installation in Sherman Oaks: What to Know First
We install Elite gates across Sherman Oaks, and most jobs take one full day from unboxing to final walkthrough. A standard single swing gate usually runs $1,800 to $3,400 installed, while a sliding driveway gate lands between $3,200 and $6,800 depending on the run of track and operator package. We quote a firm price before any work starts, not an estimate that wanders.
This page is for homeowners who already own an Elite gate or opener and want it installed properly. Whether you bought it from a dealer, inherited it with the property, or ordered the panel yourself, we’ll set it, wire it, and stand behind it. Call (818) 873-5061 and Hal will tell you what he thinks before you spend a dime.
How Elite Products Fail - and How We Fix Them
- Elite slide gate panels racking on short track runs. On compact Sherman Oaks lots where the driveway is wide but shallow, we see SL3000 and SL4000 panels binding because the track was trimmed to fit a space that’s really too tight for the panel’s cantilever design. The gate doesn’t actually fail; the geometry fails. We re-measure the setback, reweld the track supports if needed, and often add a mid-rail stiffener so the panel isn’t fighting its own momentum.
- Misplaced photo-eye height on pedestrian gates. Elite’s PED series comes with a photo-eye bracket that technically works but sits low enough to get tripped by uneven Sherman Hills walkways and planter edging. We remount the eye at the right height for your actual foot traffic and clip the lens shield so sunset glare off Ventura-facing drives doesn’t false-trigger the reverse function.
- Elite operators burning limit switches on unlevel post mounts. The ET-SL and ET-DL operators are reliable units, but if the post was poured even a half-degree out of plumb, the limit switch gets hammered on every cycle. We see this on hillside properties along Mulholland-adjacent streets where the original post was set for a chain-link gate that outlived its welcome. We reset the post or shim the operator plate and recalibrate the limits from scratch, not from the previous owner’s marks.
- Aftermarket remotes not communicating with Elite receivers. Homeowners buy generic remotes online, pair them poorly, and then blame the gate. Elite receivers run on a 318 MHz frequency and they’re pickier about clone signals than brands like Mighty Mule. We reprogram the receiver, clear ghost codes, and if your remote’s transmitter chip is actually incompatible, we source an Elite-compatible remote instead of leaving you with a paperweight.
- Weld points cracking at factory splice joints. On Elite’s double-swing DR series with decorative finial tops, the factory splices hold fine in a showroom but after three or four years of Sherman Oaks heat expansion and cold snaps, hairline cracks show at the top rail. That’s a structural seam people never see until a finial wobbles. We grind, reweld, and re-powder-coat on site so the gate doesn’t leave your driveway.
Our Elite Gate Installation Process
- 1
Call and walkthrough. You call (818) 873-5061. Hal asks what you have, what’s still in boxes, and what you’re trying to accomplish. He’ll tell you if it sounds doable and when he can be there.
- 2
Measure and inspect on site. We check the posts, the setback, the clearance, the electrical service location, and whether the Elite components you have match the opening you’re working with. If the panel’s the wrong size, we say so.
- 3
Parts decision, upfront. If the job calls for Elite OEM parts, we use them. If a quality aftermarket hinge or roller matches and saves you real money without cutting corners, we tell you both prices and let you choose. Nothing is padded.
- 4
Set, weld, and wire. We mount the gate, level it, set the travel limits, wire the operator, and connect safety edges or photo-eyes if you have them. We weld on site when the install calls for it, and we don’t hide work behind a panel we’d be embarrassed to leave open.
- 5
Test cycles and abuse check. We run the gate a few dozen times, force an obstruction mid-cycle to confirm the reverse function, and throw the manual release a couple times. If the gate binds, we fix it before we leave.
- 6
Walkthrough and paperwork. We show you what we did, reset any operator settings that need it, and hand you the invoice with the 90-Day Done Right Promise stamped in writing. If it’s not right, one call brings us back.
What Elite Gate Installation Costs in Sherman Oaks
Here’s honest money, straight from jobs we’ve done within a few miles of Ventura Boulevard. These are installed prices, including labor, hardware, and the wiring to the nearest safe power source.
- Pedestrian walk gate (Elite PED series): $900 - $1,600
- Single swing driveway gate (Elite SS series): $1,800 - $3,400
- Double swing driveway gate (Elite DR series): $3,400 - $5,800
- Sliding driveway gate with operator (Elite SL3000/SL4000): $3,200 - $6,800
- Operator replacement or addition on existing gate: $750 - $2,100
What moves the price: the condition of your existing posts, slope, electrical distance, and whether you want full automation or manual operation. We’ll give you a written quote before work begins and it won’t change at the door. Call (818) 873-5061 for a free estimate. The number gets you a live person, not a recording.
Why Sherman Oaks Homeowners Call Gatewood Fence & Gate for Elite Work
We’ve been installing and repairing Elite gates in Sherman Oaks since 2001, and most of our customers are within a few miles of the same Ventura Boulevard stretch Hal has driven every workday for over two decades. That matters when the hardware starts acting up and you need someone who remembers where the power line is buried.
We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if you’ve got a mixed-brand property or an old operator that needs replacing, we’ll tell you what actually works. The 90-Day Done Right Promise is on every invoice. The price is quoted before work starts. And if you want to see who you’re hiring, Hal’s name is on the shop and the shop is down the road.
FAQs
Most Elite limited warranties cover manufacturing defects, not installation errors, so if you set the panel out of level and the operator burns out, that’s on you. As an independent Elite service provider, we install to spec so the factory warranty stays intact on the components themselves. If something fails because the factory part was bad, you still have your claim.
Yes. Half the Elite jobs we do in Sherman Oaks start with a homeowner who bought the panel from a dealer that wouldn’t touch the install, or inherited it when they bought the house. We look at what you have, tell you if it fits your opening and your local requirements, and install it as if we’d sold it to you ourselves.
Both, and we tell you the difference before we order. Elite OEM hinges, rollers, and receivers maintain the factory warranty and fit exactly the way the manufacturer intended. On older Elite models with discontinued trim or hardware, a quality aftermarket part can keep a solid gate in service without a full replacement. We never hide the choice.
Most installations are scheduled within three to ten days, depending on our current workload and whether your job needs new posts set in concrete. If your existing posts are square and solid, we can often do the whole install in one day. Call (818) 873-5061 and Hal will give you a straight answer on timing.
If the panel is surface rusted through, not just pitted, or the stress cracks have fractured the main rail in more than one place, we’ll tell you replacement is the honest call. If the operator is dead but the panel is sound, we’d rather put a new operator on a good gate than sell you a whole new assembly. We’re in the business of keeping good gates working, not swapping things that don’t need swapping.
Give Hal a call directly at (818) 873-5061. If he doesn’t pick up he’s probably under a gate, but he’ll call you back before the hour’s out. Free estimates, no trip charge inside the county, and the price you’re quoted is the price you’ll pay.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Sherman Oaks and nearby areas.