Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Sherman Oaks Homeowners
Gate Parts & Welding in Sherman Oaks is what we do every day, and the honest answer is that most gate failures come down to a worn hinge, a cracked post, or a rail that was never welded square in the first place. At Gatewood Fence & Gate, we’ve been fixing those exact problems since 2001, and we do the welding right there in your driveway so the gate never leaves your property. Hal Gatewood started this shop with a simple rule: fix the part that’s actually broken, charge what we quoted, and stand behind the work. Every job carries our 90-Day Done Right Promise in writing, and when you call (818) 873-5061, a live person answers, day or night.
Sherman Oaks has its share of steel gates on Chandler Estates and Longridge Estates, and we know how the heat and the Santa Ana winds affect them. A gate that worked fine in May can start dragging by August because the ground shifts and the hinge post moves with it. We come out, we look, we fix it the same day in most cases. Not with a catalog of new parts you didn’t need, but with a welder, a grinder, and twenty-nine years of knowing which welds hold and which ones were somebody else’s shortcut.
What Our Gate Parts & Welding Service Includes
This is not a one-size-fits-all list. Every Sherman Oaks gate has its own history, its own load, and its own weak point. What we do is find the weak point first, then fix it properly. Here’s what that looks like, part by part.
Hinge Replacement
When a gate starts sagging, the first thing people notice is that the latch doesn’t line up anymore and they have to lift the gate to close it. That sag almost always traces back to a hinge barrel that’s worn oval or a weld that has started to crack at the hinge leaf. We don’t bolt on a new hinge and call it done. We cut off the old one, inspect the post and the frame member behind it, and weld the new hinge in after making sure the gate hangs level and the reveal is right. The hinge gets greased, the pin gets seated, and the gate opens like it did the day it was hung.
Post Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. If the post itself has rotted at the base or cracked around the weld, the hinge is fighting a losing battle. We dig out the old post, set a new one in concrete at the right depth and the right plumb, and we don’t weld the gate back on until the concrete has a real chance to cure. In Sherman Oaks, where the clay soil expands and contracts with every rain and dry spell, a post set too shallow will move within a year. We set it deep enough that it won’t.
Rail Repair
The horizontal rails carry the weight of the gate and transfer it to the hinges. When a rail has rusted through, cracked at the upright, or taken a hit from a car in the driveway, the gate will flex and eventually fail. We cut out the damaged section, weld in new steel matched to the original thickness, and grind the repair smooth so it disappears. If the whole rail is compromised, we replace it and re-weld both ends rather than splicing in a patch that will become the next failure point.
Custom Welding
Not every gate repair has a part number. A decorative scroll breaks off, an operator bracket tears out of the frame, or a homeowner wants a different panel welded in to close a gap. That’s where on-site welding changes everything. We bring the welder to you in Sherman Oaks, make the repair on the gate where it hangs, and you see exactly what was welded before we leave. If something on the gate is ornamental, we match the profile as close as steel allows, prime the burned area, and make the repair blend in.
Gate Rollers
Sliding gates and cantilever gates live and die by their rollers. A flat-spotted roller or a seized bearing makes the gate jump and grind against the track, which throws the whole frame out of square and burns out the motor. We check the wheels, the bearings, the track condition, and the guide posts, then replace the roller set with the right diameter and weight rating for the gate. A roller that’s too light will flatten again in months. A roller that’s right will roll for years.
Latch & Lock
The latch is the part you touch every day, so when it stops working, you notice immediately. A gate latch that won’t catch, a keypad that won’t release, a lock set that’s rusted stiff, these are safety issues and security issues at the same time. We rebuild or replace the latch assembly, align the strike plate, and adjust the release so it works from both sides. On automated gates, we check that the latch doesn’t fight the operator, because that fight is exactly how latches snap off and leave the gate hanging.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
We work on more than the gate itself. A lot of the time, the parts that fail are on the operator side, and we service the brands Sherman Oaks actually has bolted to its fences. BFT operators are built well, but we’ve seen the limit switch brackets wear over time and throw the travel out of adjustment. We can weld a cracked BFT post bracket back to true and set the limits so the gate stops where it should instead of slamming. Linear operators are common on apartments and commercial lots around Sherman Oaks, and we know their battery backups, their gear reduction, and the way their internal clutches behave when a gate binds on bad rollers. We carry or can get the OEM parts quickly.
We also work on Viking units on some of the larger residential gates in the hills, and Ghost Controls systems on a lot of vinyl and aluminum swing gates. What matters isn’t the logo on the box, it’s understanding how the operator talks to the gate, noticing when the travel is off, the entrapment protection isn’t engaging, and the fault is actually mechanical rather than electrical. Whether you have a BFT, Linear, Viking, Ghost Controls, or any other make, if it’s a gate, we can look at it and tell you honestly what it needs.
Signs You Need Gate Parts & Welding Right Now
Most gate failures announce themselves early, but only if you know what you’re looking at. If you see any of these on your Sherman Oaks gate, don’t wait for the whole thing to drop. Call (818) 873-5061 and we’ll come see it.
- The gate drags on the ground or scrapes the driveway. This is almost never a mystery. The hinge side has dropped, which means a hinge, a post, or a weld is failing. The longer it scrapes, the more weight the operator pulls and the more strain on every other joint.
- You have to lift the gate to get the latch to line up. That is a hinge problem, full stop. Lifting the gate every day just accelerates the wear and eventually rips the latch off the post. Fix the hinge, and the latch lines up on its own.
- The gate swings open or closed on its own. Show me the gate closing on its own and I’ll show you where it’s failing. Usually it’s a post that is no longer plumb, and gravity is doing the rest. A gate that moves by itself is also an entrapment hazard for kids and pets.
- You can see rust flaking around a weld or the steel has a crack running through it. A crack doesn’t heal. It grows every cycle the gate opens and closes. If you catch it early, a few minutes of welding fixes it. If you wait until the rail separates, the repair gets bigger and the gate gets dangerous.
- The gate shakes or bounces while it moves. Sliding gates that bounce have a roller that’s flat-spotted or a track that has shifted. Swing gates that shake have a hinge pin that’s wallowed out its bushing. The shake is the symptom; the worn part is the disease.
Our Gate Parts & Welding Process - Step by Step
We don’t do drama and we don’t do surprises. When you call us for gate parts or welding in Sherman Oaks, here’s exactly what happens.
- 1
You call and a real person answers. When you dial (818) 873-5061, the person who picks up is us, not a call center. We ask what the gate is doing, we ask where you are in Sherman Oaks, and we get you on the schedule. If it’s an emergency, we come out the same day.
- 2
We come out and inspect the gate where it sits. Hal shows up, walks the gate, checks the hinges, posts, rollers, track, and operator if there is one. We look at how the gate hangs, how it opens, and where the wear pattern is. The diagnosis happens in your driveway, not over the phone, because guesses over the phone cost you money.
- 3
We show you what we found and quote the repair before we touch anything. You get a number, in writing, before the welder fires up. No trip charge inside the county, no “well it turned out to need more” after the fact. If the written estimate from another company says something different, bring it to us and we’ll give you a free second opinion.
- 4
We do the work on site. We cut, weld, grind, set posts, replace rollers, rebuild latches, and test everything under load. If the gate has an operator, we run it through its full cycle and check the force settings and the safety edges so it doesn’t work against the mechanical repair we just made.
- 5
We walk you through the work before we leave. You see what was welded, what was replaced, and why. We clean up the grinding dust and the cut-off scraps. Then you get the 90-Day Done Right Promise in writing, which means if the repair isn’t right, one call brings us back. No runaround.
How Much Does Gate Parts & Welding Cost in Sherman Oaks?
If you’re wondering how much Gate Parts & Welding costs, it runs a wide range because a hinge replacement and a post replacement are different jobs. A typical hinge replacement with on-site welding runs $180 to $320 depending on the size of the gate and how much steel we have to move. Post replacement runs $450 to $900, and that includes digging out the old post, setting a new one in concrete, and re-hanging the gate. Rail repair falls between $250 and $550, depending on how much rail has to be replaced. Custom welding jobs get quoted per job, but we’ll give you a number before we start, and that number is what you pay.
What affects the price: the thickness of the steel, the condition of the surrounding structure, whether the gate needs to come off its hinges or can be repaired in place, and whether the operator has to be re-aligned afterward. We don’t pad quotes with parts that don’t need changing. If a hinge is bad, we replace the hinge. If the post behind the hinge is still solid, we leave it alone. And every quote, every single one, is agreed upon before any work starts. You’ll never get a different number at the door. Also, if your repair is over $200, you get $40 off, and seniors and veterans always get 10% off, permanently.
Gate Parts & Welding Near Sherman Oaks - Our Service Area
We work all over the San Fernando Valley and across the hills. Sherman Oaks is home base, but you’ll see our trucks in Gate Parts & Welding in Los Angeles, down in Gate Parts & Welding in Santa Monica, and all through Van Nuys, Encino, Tarzana, North Hollywood, Studio City, Reseda, and Northridge. If you’re up in the hills around Beverly Glen or in the flats south of Ventura Boulevard, call us. We know the streets, and we know how the soil and the sun work on a gate. Typical response in Sherman Oaks is same day for calls before noon, next morning after that.
If you want to know more about the rest of what we do, start at our home page for fence and gate work across the Valley.
Serving Sherman Oaks, CA - Our Local Coverage Area
We’re based in the Sherman Oaks area and know this community well, and we also provide Gate Parts & Welding in Van Nuys. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Sherman Oaks
Gate parts & welding is the work of replacing or repairing the structural and mechanical components of a gate, hinges, posts, rails, rollers, latches, locks, plus the actual welding of steel to steel. It’s not just bolting on new hardware, it’s cutting, fitting, welding, and grinding so the gate operates like it did when it was built. That’s the difference between a repair that lasts and one that fails again in six months.
Most hinge replacements, latch rebuilds, and roller swaps are done in two to four hours on site. A post replacement takes longer because the concrete has to cure before we re-hang the gate, usually meaning we’re back the next day to finish. We’ll tell you upfront how long the job will take based on what we find, and we stick to that schedule. Call (818) 873-5061 to get a time estimate for your specific gate.
As covered above, typical ranges are $180 to $320 for hinge work, $450 to $900 for post replacement, $250 to $550 for rail repair, and rollers or latches in the $150 to $400 range depending on the part. We quote the job in writing before any work starts, and that’s the price you pay. Estimates are free, and we’ll give you an exact number after seeing the gate, not before.
We do. Gatewood Fence & Gate is certified to service LiftMaster along with FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If the mechanical repair touches the operator, we re-align the travel, check the clutch or force settings, and make sure the gate’s automation and its structure are working as one piece. If you have a LiftMaster and something isn’t right, call us and we’ll diagnose it honestly.
Yes. If your gate is stuck open, stuck closed, or off its track and your property is unsecured, call (818) 873-5061 right now. A live person answers 24 hours a day, 7 days a week, and we’ll get someone out to Sherman Oaks the same day in the vast majority of cases. We prioritize security issues because a gate that won’t close is the same thing as no gate at all.
Every job carries our 90-Day Done Right Promise in writing. If the repair is not done right, one call brings us back to make it right, no runaround and no debate. We’ve been doing this since 2001, and Hal Gatewood’s name is on the shop. That’s the oldest warranty in the book: the name on the invoice matches the guy who did the work.
Clear the area around the gate so we have room to work, move any cars out of the driveway, and if you have dogs, keep them inside while we’re welding. That’s about it. We bring the welder, the grinder, the steel, and the parts. You don’t need to have anything ready except the gate itself. If there’s a gate code or a driveway gate, tell us when you call so we can get in without hassle.
Schedule Your Gate Parts & Welding Service in Sherman Oaks Today
If your gate is sagging, scraping, cracking, or just not right, call (818) 873-5061 and talk to a person who has been doing this since 2001. We’ll come out to Sherman Oaks, or you can reach our Gate Parts & Welding in Encino team, look at the gate where it hangs, and give you a written quote before any work starts. Free estimate, no trip charge inside the county, and a 90-Day Done Right Promise in writing. One call, and it gets fixed.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Sherman Oaks since 2001.