Ghost Controls Gate Installation Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Installation in Sherman Oaks: What to Know First

Ghost Controls gate installation in Sherman Oaks typically runs $450-$1,400 depending on whether it’s a single swing gate, a double gate, or a sliding setup, and most jobs are completed in one day once we have the kit in hand. We install and service Ghost Controls openers on existing driveway gates, pedestrian gates, and new gate builds across Sherman Oaks, and we quote the full price before any work begins. This page is for homeowners who already own a Ghost Controls system, or are thinking about buying one, and want to know exactly what installation actually involves in this neighborhood. Call us at (818) 873-5061 and we’ll talk you through it. You’ll get Hal or someone who works with him every day, not a menu tree. As an independent Ghost Controls service provider, we’re not the manufacturer, but we know these openers well enough to spot their problems before they leave you stuck at the curb.

Call (818) 873-5061

Key takeaways:

• We install and repair Ghost Controls openers on swing, slide, double, and pedestrian gates in Sherman Oaks.
• Free estimates, upfront pricing, and the 90-Day Done Right Promise on every job.
• We weld on site, so your gate never leaves your driveway unless it absolutely has to.
• Same-day service is often possible for a gate that won’t open, not for a brand-new installation, which gets scheduled and quoted properly.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls makes a solid opener for the money, but we see the same handful of problems across Sherman Oaks driveways, and most of them trace back to installation shortcuts or wear from the sun and the slope. Here’s what actually happens out here:

• Phantom “obstruction” alarms on the AXDP and TSS1 series. The control board reads resistance spikes as an obstruction and reverses the gate mid-cycle. Nine times out of ten, it’s not the board. It’s a hinge post that’s leaning, a wheel that’s dragging, or a gate that someone hung a half-inch too low. We fix the mechanical problem first. A new board on a binding gate just burns out the same way the old one did.
• Slow or jerky travel on the AXS series, especially on sloping lots. Ghost Controls openers run a soft start/stop curve, and when a gate pulls hard against a slope or a wheel that’s out of round, the motor hunts and the gate shudders. In the hills above Ventura Boulevard, we see this constantly. Correcting the gate’s travel height and freeing up the wheels usually smooths it out without touching the opener.
• Remote range that drops to twenty feet. Most Ghost Controls installs put the antenna receiver behind a stucco wall or a metal gate frame, and stucco with wire lath eats signal. We relocate the antenna or add an external receiver, and the range comes back. If the system is older, the remotes may just be tired, and we replace them with genuine Ghost Controls parts so the warranty stays intact.
• Battery backup that dies in under a year on the Ghost Controls kits. The batteries in the solar and backup kits don’t love the heat, and here where summer pushes ninety-plus for weeks at a time, they fail faster than the manufacturer’s ideal specs. We test the battery under load, not just with a voltmeter, because a battery that reads 12 volts at rest can still collapse when the gate starts moving.
• Gate leafs that drift after the opener stops. If the gate won’t stay fully open or fully closed, the limit sensors are fighting the gate’s natural resting point. On double gates, we often find one leaf is a quarter-inch ahead of the other, which makes the opener work harder and the magnets and limit switches go out of adjustment. We square everything up before we adjust the limits.

Our Ghost Controls Gate Installation Process

Every Ghost Controls job follows the same quiet, measured sequence. No mystery, no surprises.

1. 1
   You call (818) 873-5061. A live person answers. We ask about your gate: swing or slide, single or double, wood or metal, and whether the opener is already on site or you’re still deciding.
2. 2
   We come out and look. Before we quote an installation, we see the gate in person, check the hinges, the posts, the ground slope, and where the power is or needs to be. A Ghost Controls opener on a sagging gate is a warranty claim waiting to happen, so we measure before we promise anything.
3. 3
   You get a written price. The full price, part by part and pound for pound. If the post needs welding or the gate needs a shim set, it’s in the quote, not a surprise at the end. We don’t start until you’ve agreed to the number.
4. 4
   We install or fix the gate first, then the opener. The opener only works as well as the gate it’s bolted to. We square the gate, fix the hinges, free the wheels, and then mount the Ghost Controls unit, wiring it to the company’s spec. We use OEM Ghost Controls hardware where it matters, and honest aftermarket parts where OEM is overpriced. You’ll know which is which before we buy anything.
5. 5
   We test it in front of you. Open, close, stop, reverse, photo eye, remote, keypad. We test the gate under the same conditions you’ll use it, and we don’t leave until it cycles clean a dozen times in a row.
6. 6
   You get the 90-Day Done Right Promise in writing. If anything we touched fails in the next ninety days, one phone call brings us back. That’s stamped on the invoice, not implied.

What Ghost Controls Gate Installation Costs in Sherman Oaks

Ghost Controls gate installation in Sherman Oaks is not a mystery when you know what you’re paying for. Here’s the honest picture:

• Single swing gate, opener already on hand: $450-$750
• Double swing gate, opener already on hand: $700-$1,100
• Sliding gate, opener already on hand: $650-$1,000
• New Ghost Controls opener plus installation: $1,000-$1,400
• Wiring for a gate with no existing power run: quoted after we see the distance and terrain

What moves the price: whether the existing gate is square or needs correction, the length of the power run, whether the gate is wood or steel, and which Ghost Controls series you’re installing. We’ll give you a free estimate before we touch a tool, and the number we quote is the number you pay. Call (818) 873-5061 to have Hal or one of us come out and see the gate in person. No trip charge inside the county.

Why Sherman Oaks Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

We’ve been at this in Sherman Oaks since 2001, and that’s not a marketing line. Hal Gatewood’s name is on the shop, his address is published, and you can drive by and see the trucks. That matters to the kind of person who’s already been burned once by a company that quoted one price on the phone and another at the door. Around here, your neighbor’s gate probably has our weld on it. We also service LiftMaster, Mighty Mule, and DoorKing systems, so if you ever switch brands or need a second opener on the property, we’re not going to pretend Ghost Controls is the only answer. The 90-Day Done Right Promise is on every invoice, in writing. And when you call at 9 p.m. because your gate won’t close, a live person answers. Not a voicemail. Not a chatbot. Hal picked up the trade at Los Angeles Valley College over in Valley Glen, took their welding and metal fabrication courses, and he’s been under Sherman Oaks gates ever since. Give me a call directly, if I don’t pick up I’m probably under a gate, but I’ll call you back before the hour’s out.

FAQs