Linear Gate Access Control Nationwide | Gatewood Fence & Gate

Linear Gate Access Control in Sherman Oaks: What to Know First

We repair, replace, and upgrade Linear gate access control systems throughout Sherman Oaks, and most jobs are finished in a single visit because we carry the common Linear parts on the truck. The honest cost picture: a keypad replacement runs $240-$380, a full access control upgrade with phone entry lands between $800 and $1,600, and you’ll know the exact price before we touch anything. This page is for the homeowner who owns a Linear system, wants it fixed right without a sales pitch, and doesn’t want to gamble on a franchise that will try to sell them a whole new gate. Call Hal at (818) 873-5061 and get a straight answer on whether your Linear system is worth saving.

Call (818) 873-5061

How Linear Products Fail - and How We Fix Them

Linear has been building gate operators and access control for decades, and in Sherman Oaks we see the same failure patterns repeat themselves. Here’s what actually goes wrong, and what we do about it.

• Linear MegaCode keypad (AK-11, AP-3, AM-KP) stops accepting the code. Nine times out of ten this is a corroded ribbon cable inside the keypad housing, not a dead keypad. Sherman Oaks gets marine layer moisture rolling up the Sepulveda Pass, and that condensation works its way into any housing that wasn’t sealed right. We open the keypad, clean the contacts, replace the ribbon if needed, and reseal it with a gasket that actually holds. A new keypad from a big-box installer would’ve cost you $300 for the same problem to come back in two years.
• Linear M3 / L3 / G series gate opener won’t respond to the remote but works fine from the keypad. This is almost always the receiver board’s antenna wire, which gets brittle after a few years of sun exposure on the Sherman Oaks side of the hill. It snaps inside the housing where you can’t see it. We replace the antenna lead, re-tune the receiver, and your remotes work again without buying a whole new board. Linear wants you to replace the receiver; you don’t have to.
• Linear telephone entry system (AE-100, AE-2000, AM-D) dials but no one can hear the resident. The microphone element on these units sits behind a thin foam cover that breaks down in direct Sun Valley heat. We replace the mic element and the foam with a UV-stable material that survives more than two summers. This is a $90 fix on a part most companies won’t touch because it requires bench work.
• Linear access control power supply (PS-12, PS-24) hunts and drops voltage. The transformer in these units was never rated for continuous duty in a hot Sherman Oaks afternoon. When it starts to go, your keypad lights flicker, the relay chatters, and the gate opens when it shouldn’t. We replace the transformer with a higher-rated unit and mount it on standoffs so air can move. Linear’s own spec sheet doesn’t mention thermal derating; we learned it by opening fifty of these things and seeing the same scorch mark.
• Linear card reader (AM-CR, PR-1) only reads every third swipe. The reader head gets a film of dust and oxidized plastic that blocks the RFID signal. Completely invisible, completely fixable. We pull the faceplate, clean the reader head with a non-conductive solvent, and it reads clean again. The parts cost for this job is about twenty cents; the knowledge costs what it costs.

Our Linear Gate Access Control Process

Here’s what a Linear access control service call looks like when you bring us in. No mystery, no upselling, no parts you don’t need.

1. 1
   You call (818) 873-5061. A live person answers, asks which Linear product you have and what it’s doing. We schedule the window that works for you, and we show up in it.
2. 2
   Diagnostics on site. Hal or one of his crew opens the enclosure, puts a meter on the power supply, checks the relay contacts, and watches the system run through its cycle. We look for the failure, not for a commission.
3. 3
   Parts decision laid out plainly. If the part is critical to safety (a relay that feeds the open command, a keypad that controls a swinging gate over a driveway), we use OEM Linear parts. If it’s a cosmetic keypad bezel or a mounting bracket, we’ll offer a quality aftermarket part at half the cost. You decide with the facts in front of you.
4. 4
   Repair or replacement, then a full test cycle. We run the gate through open, close, obstruction, and remote-trigger tests. If it fails once, we don’t call it done.
5. 5
   Cleanup and the 90-Day Done Right Promise. We close the enclosure right, leave no wire clippings, and hand you a written guarantee. If anything on that repair fails in 90 days, one call brings us back, no runaround.

What Linear Gate Access Control Costs in Sherman Oaks

Here are real numbers from our trucks in Sherman Oaks, not an average from a national database.

• Linear keypad replacement (AK-11, AP-3): $240-$380 depending on whether we’re reusing your existing wiring or running new.
• Telephone entry system repair (AE-100, AE-2000): $180-$420 for mic replacement, relay work, or wiring harness repair.
• Linear remote programming and receiver tuning: $85-$150 if we’re already on site; $120-$190 as a standalone call.
• Full access control upgrade (phone entry, card reader, keypad, new receiver): $800-$1,600 depending on the Linear model and whether we need to pull new cable through the post.
• Power supply replacement (PS-12, PS-24): $150-$275 with a thermally rated transformer.

What moves the price: whether the existing wire can be reused, whether your Linear enclosure needs welding repair, and whether you want OEM or quality aftermarket parts. Every price gets quoted and agreed before work starts. Call for a free estimate, and we’ll tell you the number on the phone before we ever schedule the truck.

× ‹ ›