FAAC Gate Access Control Nationwide | Gatewood Fence & Gate

FAAC Gate Access Control in Sherman Oaks: What to Know First

FAAC gate access control repair in Sherman Oaks typically runs $225 to $485 depending on whether we’re replacing a keypad, rewiring a phone entry system, or rebuilding a swing-arm operator that’s stopped talking to the board. Most jobs are done the same day, and we quote the full price before we touch a screwdriver. This page is for FAAC owners in Sherman Oaks who want straight answers about why their keypad went dark or why the gate only opens for the remote half the time. If that’s you, call (818) 873-5061 and you’ll get Hal or someone who works beside him, not a machine.

Call (818) 873-5061

How FAAC Products Fail - and How We Fix Them

FAAC builds solid operators, but around Sherman Oaks we see the same patterns crop up on specific models. Here’s what actually goes wrong and what we do about it.

• FAAC 400 Series swing operators losing their limits. The 400 series uses magnetic limit switches that drift over time, especially on gates that get a lot of cycles from Valley traffic near Ventura Boulevard. The gate starts over-traveling by an inch, then three, then it slams the stop. We re-align the limits, test the full sweep, and usually have it back in an hour without swapping the board.
• FAAC E024U control boards with dead keypad ports. Sherman Oaks has older homes with original FAAC E024U boards still in service. The keypad terminal block corrodes from morning marine layer moisture, and the board stops reading keypad input even though the remote still works. We repin the terminal, seal it with dielectric grease, and replace the board only when the traces are gone.
• FAAC 844 ER photobeam misalignment after landscape work. It’s almost always a gardener’s weed whacker or a new hedge. The 844’s beams are sensitive, and once they’re off-axis by a half degree the gate refuses to close on auto. We square the beams, test them in full sun, and set the fail-safe mode so the gate holds open instead of shutting blind.
• FAAC receiver modules dropping intermittent remotes. The plug-in receiver on older FAAC units loses its memory in heat waves, and Sherman Oaks gets plenty of those in August. Homeowners report remotes working in the morning and dead by 3 pm. We replace the receiver module with a current-spec unit, reprogram all remotes at the panel, and test at the street and at the driveway before we leave.
• FAAC hydraulic operators with slow leak-down on sloped drives. Sherman Oaks has enough hillside driveways that we see this constantly. The pump seal weakens, the gate creeps down overnight, and the auto-close timer keeps cycling. We replace the seal, top the reservoir, and check the manual release so the gate stays where the board tells it to.

Our FAAC Gate Access Control Process

1. 1
   You call (818) 873-5061. Hal or someone on his crew answers. We ask what the gate is doing, what model it is if you know, and when it started.
2. 2
   We show up with FAAC parts on the truck. We keep common boards, receivers, keypads, and limit switches stocked so we’re not driving back to a parts counter on your dime.
3. 3
   We diagnose the whole access system, not just the symptom. If the keypad is dead but the board is fine, we’re not selling you a board. We trace the wire to the actual failure and show you what we found.
4. 4
   We give you the price before we start. For any repair over $200, you get $40 off. Seniors and veterans get 10% off, always. No trip charge inside the county. The number we quote is the number you pay.
5. 5
   We repair, test, and stand behind it. We test the keypad, remote, phone entry, and safety edges in every combination we can think of. Then we watch the gate complete ten full cycles before we pack up.
6. 6
   You get the 90-Day Done Right Promise in writing. If it acts up within 90 days, call. We make it right. No phone tree, no “we’ll send someone next week.”

What FAAC Gate Access Control Costs in Sherman Oaks

Here’s what FAAC access control work runs in Sherman Oaks, based on what we see most weeks:

• Keypad replacement (FAAC XKPR or compatible): $225 to $340, including programming all existing codes.
• Receiver module replacement and remote reprogramming: $180 to $290, depending on how many remotes you run.
• Photobeam alignment or replacement (FAA 844 ER): $150 to $275. Alignment alone is usually on the low end.
• Control board replacement (FAAC E024U or newer): $350 to $485 for the board, labor, and full system test.
• Phone entry / intercom integration on a FAAC operator: $300 to $550, depending on whether we’re wiring an existing system or adding a cellular unit.

What moves the price: how far the operator is from the house panel, whether we’re running new wire through concrete, and whether the original installer left anything worth saving. We’ll tell you the number before we start, and that price holds. Call (818) 873-5061 for a free estimate, or bring a written quote from another company and we’ll give you a free second opinion on it.

Why Sherman Oaks Homeowners Call Gatewood Fence & Gate for FAAC Work

We’ve been fixing gates in Sherman Oaks since 2001, and most of our customers are within a few miles of the Ventura Boulevard stretch we’ve driven every workday for over two decades. Hal Gatewood’s name is on the shop and on every invoice. If he says a board is dead, he’ll show you the burned trace. If we can weld a hinge back and save you a $900 panel, we’ll do it in your driveway and tell you exactly why the repair will hold.

We service nine major gate brands, and when we’re on a FAAC job we also know how the LiftMaster, Mighty Mule, Ghost Controls, and DoorKing systems behave. That matters when an access system has a mix of brands, which happens more often than you’d think. The 90-Day Done Right Promise is written on every job ticket. Calls get answered by a live person, 24/7. No voicemail, no dispatch queue, no “press 1 for service.”

FAQs