FAAC Gate Repair Nationwide | Gatewood Fence & Gate

FAAC Gate Repair in Sherman Oaks: What to Know First

FAAC gate repair in Sherman Oaks typically runs $185 to $450 for most operator and hinge failures, and we can usually have your gate working again within one to two days of your call. That’s the honest range - the final number depends on whether we’re replacing a control board, rebuilding a gate hinge, or welding a cracked frame member. If you own a FAAC system and the gate won’t open or is making noise it didn’t make last week, this page tells you what’s actually wrong and what it costs to fix. We’re Gatewood Fence & Gate, an independent FAAC service provider in Sherman Oaks since 2001. Call (818) 873-5061 and Hal or one of our crew will answer.

Call (818) 873-5061

How FAAC Products Fail - and How We Fix Them

• FAAC 400 and 402 operators losing their limit settings. These compact 24V operators are common on Sherman Oaks driveway gates, and after four or five years of heat cycling, the internal limit switches drift. The gate starts stopping six inches short of closed, or it reverses for no obvious reason. We open the operator, re-set the limits mechanically, and replace the worn limit cam if it’s cracked. This is a $90 to $160 fix, not a new operator.
• FAAC 750 and 760 hydraulic operators with noisy or slow movement. These are the workhorses on heavier iron gates in the hills above Ventura Boulevard. When they get sluggish or start groaning, it’s almost always low hydraulic fluid or a bypass valve that’s drifted out of adjustment. We top off the fluid, pressure-test the valve, and if the pump is cavitating we rebuild it rather than quoting you a whole new unit. A full operator replacement is the last card we play.
• FAAC S418 and S450 swing-arm actuators binding on Sherman Oaks clay soil. Here’s something FAAC’s manual won’t tell you: the clay-heavy soil in Sherman Oaks shifts with every wet winter and dry summer. Gate posts move, the swing geometry changes, and the actuator arm starts fighting the gate instead of driving it. We re-set the post, realign the arm, and re-torque the mounting hardware to factory spec. In Natomas we see spring failures from dry heat; in Sherman Oaks it’s post shift from clay expansion.
• FAAC control boards (E024U and 455D) tripping after rain. The 455D board in particular doesn’t love moisture. When a Sherman Oaks gate starts tripping its breaker or the keypad goes dead after a rainstorm, we find corroded terminal blocks or a compromised weather seal on the enclosure. We clean the board, replace the terminals if they’re pitted, and reseal the box. Unless the board is fried, you’re looking at an hour of labor, not a $600 part.
• FAAC photocells and safety edges failing intermittently. FAAC gates rely on photocells and resistive edges to stop and reverse. When the gate reverses halfway or won’t close at all, it’s usually a misaligned photocell or a cracked safety edge that’s sending a false obstruction signal. We test each component individually, identify which one is lying to the board, and replace only what’s failed. Some shops shotgun all four sensors. We’d rather charge you for one.

Our FAAC Gate Repair Process

1. 1
   You call, a person answers. Hal or someone on our crew picks up at (818) 873-5061. We ask what the gate is doing, what lights are flashing on the board, and whether it makes noise. That tells us a lot before we even get in the truck.
2. 2
   We show up and diagnose in front of you. We don’t haul your gate off. We bring the multimeter, the pressure gauge, and the welder to your driveway. You’ll see exactly what we see.
3. 3
   Parts decision: OEM or quality aftermarket. If your FAAC operator is under manufacturer warranty, we use FAAC OEM parts so that warranty stays intact. If it’s out of warranty, we talk through the trade-off: OEM is sometimes twice the price for the same board with a different sticker. We quote both when it’s a wash, and we let you decide.
4. 4
   The repair happens on site. Welding, hinge re-pinning, board replacement, actuator rebuild - it all happens at your house. We don’t subcontract and we don’t take your gate to a shop.
5. 5
   We cycle the gate 15 to 20 times and make you watch. Show me the gate closing on its own and I’ll show you where it’s failing. If it passes in front of you, it’s fixed.
6. 6
   You get the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings us back, no runaround.

What FAAC Gate Repair Costs in Sherman Oaks

Here’s what we charge for the FAAC jobs most Sherman Oaks homeowners call about:

• Diagnostic visit: $75, waived if we do the repair. If another shop quoted you a repair and you want a second opinion, bring us the written estimate and the second look is free.
• Limit switch or solenoid replacement on a FAAC 400/402: $90 to $160
• FAAC 455D control board replacement: $340 to $520 depending on OEM vs aftermarket
• Hydraulic pump rebuild on a FAAC 750/760: $280 to $450
• Gate hinge re-pinning and realignment: $150 to $350 depending on how far the post has drifted
• Full operator replacement (parts and labor): $850 to $1,400 installed

What moves the price is parts cost and whether we’re welding. The quote we give you on the phone is the quote on the invoice - we don’t arrive and discover a “new problem” that doubles the bill. Before any work starts, you get a number and you agree to it. Call (818) 873-5061 for an exact quote on your FAAC system.

Why Sherman Oaks Homeowners Call Gatewood Fence & Gate for FAAC Work

Hal Gatewood started working on gates in Sherman Oaks in 2001, and he’s still the one whose name is on the invoice. We repair what other companies want to replace. If a FAAC operator can be rebuilt for $300, we’re not going to try to sell you a $1,200 replacement. If a gate post can be welded and re-pinned instead of dug out and reset, we’ll weld it in your driveway. And we know FAAC the way you only learn by opening a few hundred of them - the quirks, the weak points, and the fix that lasts. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, which matters when a new FAAC board needs a day to arrive and we can temporarily rewire your gate to a universal receiver so it still opens while the part ships. Every job carries the 90-Day Done Right Promise in writing, and a live person answers our phone 24/7. If we can’t fix it, we tell you plainly. If we can, we do it right the first time.

FAQs