Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across West Hollywood
Gate repair in West Hollywood usually means one of three things: a hinge post that has rotted out, an operator board that has burned through from constant cycling, or a gate that slammed loose during a Santa Ana event and now hangs crooked off its track. Typical repairs here run $180-$640 depending on whether we are welding on site, replacing a board, or resetting a post. We have been fixing gates since 2001, and we answer the phone with a live person any hour you call. Hal Gatewood’s name is on the shop, and the crew that shows up at your WeHo address works directly for him.
If your gate is down, sagging, or opening halfway and stopping, call (818) 873-5061. We give you a price before we pick up a tool, and that price does not change at the door.
Why Gatewood Fence & Gate Is West Hollywood’s Preferred Gate Repair Company
Most gate companies in Los Angeles County will tell you they serve West Hollywood, but they are working off a map, not a habit. We actually know the difference between a bungalow court off Fountain Avenue and a high-rise condo on Doheny Drive, because we have been pulling permits, welding posts, and swapping operators in this 2.4-square-mile city for years. The person who answers your call has been up Santa Monica Boulevard in traffic and knows the building department’s permit counter on a first-name basis.
Hal Gatewood founded this shop in 2001 and still runs it himself. That means when we promise upfront pricing, a live person on the phone, and the 90-Day Done Right Promise on every job, it is his word, not a script. Our Gate Repair crew does the work in your driveway. We do not haul your gate to some shop across town unless there is no other way to do it right. And before we cut into a stucco pilaster or swap a Viking operator on a shared entry gate, we check the WeHo permit picture ahead of time so you are not standing in front of a stop-work order from the city’s Community Development Department.
Our Gate Repair Services in West Hollywood
Electric Gate Repair
An electric gate that hums but does not move, opens a few inches and reverses, or trips the breaker repeatedly is usually fighting a failing capacitor, a corroded limit switch, or a board that has absorbed too many power surges. In West Hollywood, shared entry gates on buildings along Santa Monica Boulevard and Fountain Avenue often run a Viking Access or Elite West Hollywood Gate Motor & Opener that cycles 50-100 times a day, which murders circuit boards on a timeline you would not see in a single-family driveway. We test the board, the battery backup, and the loop detector before we quote a repair, because replacing a $400 board when a $40 limit switch is the culprit is not how we work.
Automatic Gate Repair
Automatic gate failures in this part of Los Angeles frequently trace back to the operator, but the operator itself is rarely the whole story. Salt air, UV exposure, and Santa Ana wind loads stress every component together: the hinges corrode, the post shifts, and the operator burns out trying to push a gate that no longer swings true. Our Gate Repair in West Hollywood work always starts with the question “what is the gate actually doing wrong?” rather than “which part do we swap first?” Show us an automatic gate that is closing on its own or stopping mid-travel, and we will trace the failure to its real source.
Hinge & Post Repair
The hinge post is where most West Hollywood wrought iron gates die. It is not the gate panel that fails first; it is the post the panel hangs from, especially within a half-mile of the ocean influence where salt air drives galvanic corrosion between the steel post and the aluminum hinge bracket. We dig out the rotted footing, reset the post in concrete, and switch to stainless fixings so the repair lasts longer than the original. A gate sags in the hinge post, not in the middle, and that is where we start.
Gate Realignment
After a strong Santa Ana event, a swing gate that used to close flush now catches on its latch, and a slide gate hops its track. That is not always a bent panel. Often the post has shifted a half inch, or a pivot bolt has sheared. In West Hollywood, older wrought iron gates from the 1940s and 1950s were hung on hardware that was never sized for the lateral gusts that blow through the hills and canyons October through December. We realign the post, true the hinges, and replace the hardware with heavier-duty stock where the wind load demands it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in West Hollywood
We service and repair most major gate operator brands, and we keep common parts for our Gate Parts & Welding in West Hollywood stocked so you are not waiting a week for a shipping label. If your building runs a Viking shared gate operator, we have seen that exact model fail on that exact cycle count before. Same with Linear, BFT, and Ghost Controls units on single-family homes near Sunset Boulevard. We are certified on nine major brands, but the certification matters less than the fact that we have been inside these boards enough times to know what fails first in this city. If the brand on your opener is not one we carry, we will still come out, diagnose it, and give you a straight answer about whether it is worth repairing or replacing.
Common Gate Repair Problems We See in West Hollywood Homes
- Salt-air hinge post rot. Within a half-mile of the ocean, steel gate frames and aluminum operator brackets eat each other through galvanic corrosion. The post fails years before the gate panel does, and the fix is a reset post with stainless fixings, not a fresh coat of paint.
- Santa Ana wind sheared pivot bolts. October through December, dry gusts slam 60-year-old swing gates hard enough to snap the original pivot hardware. If your gate bangs open in a specific wind direction, call before it takes the post with it.
- Shared entry operator burnout. On dense multi-unit corridors, gate operators run 50-100 cycles a day. Viking and Elite circuit boards and battery backups die on a compressed timeline, and when they go, the whole building loses access at once.
- UV-degraded seals and housings. West Hollywood gets intense sun without the coastal marine layer to soften it. Plastic operator housings crack, rubber seals turn to powder, and powder coatings chalk. It is not cosmetic; once the housing splits, the board inside is on borrowed time.
Pricing for Gate Repair in West Hollywood, CA
Gate repair in West Hollywood runs on honest ranges, and we give you a firm number before any work starts. Here is what our customers typically see:
- Hinge or post repair: $180-$520 depending on whether the post needs a new footing or just new hardware
- Weld and rust repair on a wrought iron gate: $220-$640 including on-site welding and surface prep
- Operator board or limit switch replacement: $190-$480 for most Viking, Linear, BFT, and Ghost Controls units
- Full gate realignment after a wind event or post shift: $160-$380
- Shared entry operator diagnosis and repair: $150-$550, quoted upfront after the diagnosis
The price we quote is the price you pay, agreed before we pick up a tool. We also offer $40 off any repair over $200, a free second opinion on any written estimate, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (818) 873-5061 for an exact quote. The estimate is free, and we will not upsell you on parts you do not need.
How West Hollywood’s Permit Process Changes Your Gate Repair
West Hollywood is its own incorporated city with its own Community Development Department, which means a gate replacement or new Gate Access Control in West Hollywood installation here requires a WeHo permit, not an LA City permit. Contractors who assume LADBS rules apply get it wrong regularly, and the consequence is not a slap on the wrist. It is a stop-work order that can leave an entire apartment building without functioning gate access. We pull the permit before we cut into the stucco or re-pour a footing. On a 1940s bungalow court off Fountain Avenue, our crew replaced a corroded wrought iron pedestrian gate whose hinge post had rotted through after decades of salt-laden air. We reset the post in a new footing with stainless fixings, migrated the Viking operator’s loop detector to the new threshold, and had the building’s stop-work risk cleared by pulling the WeHo permit before we even cut into the stucco pilaster. That is the difference between a repair that holds and a repair that gets shut down mid-project.
We Also Serve Cities Near West Hollywood
If you are a few minutes outside WeHo, we cover those neighborhoods too. Our West Hollywood customers are neighbors with people in Beverly Hills, Studio City, North Hollywood, and Sherman Oaks, and we run repairs across all of them. The salt-air and wind-load patterns shift slightly as you move inland, and we adjust the materials and hardware accordingly. If your gate is acting up and you are not sure whether you are in our service area, call (818) 873-5061 and ask. A live person picks up.
Serving West Hollywood, CA - Our Local Coverage Area
We’re based in the West Hollywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in West Hollywood
Yes. West Hollywood’s Community Development Department requires a WeHo permit for a new automated gate operator, even if the gate itself is staying put. The city operates under its own municipal code, not LADBS, and contractors who skip this step have triggered stop-work orders that shut down building access. We handle the permit before we start the install. Call (818) 873-5061 and we will walk you through the timeline for your specific setup.
The hinge post fails first, almost always. Salt air drives galvanic corrosion between the steel post and the aluminum hinge bracket, and the post rots from the inside out years before the gate panel or the operator board gives up. That is why we reset posts with stainless fixings instead of just patching the rust. If your gate is sagging near the hinge side, call before the post lets go completely.
Santa Ana events, which peak October through December, bring dry lateral gusts that hit older swing gates hard enough to shear pivot bolts and knock slide gates off their tracks. The original hardware on a 60-year-old wrought iron gate was never sized for that kind of wind load. If your gate bangs or skips during a wind event, that is the warning sign, and the repair gets more expensive if you wait until the post shifts too.
Yes, in most cases we can diagnose and repair the operator without closing the gate to residents, especially if the failure is in the board, battery backup, or loop detector rather than the gate structure itself. On buildings running Viking Access or Elite operators, we have seen board burnout from 50-100 cycles a day and can usually swap the failed component same-day. If a post or hinge is the problem, we schedule the repair around building access and pull the WeHo permit first. Call (818) 873-5061 and we will give you a straight answer on timing.
Galvanized steel lasts longer, period. Painted steel on a gate exposed to West Hollywood’s salt air and intense UV will start showing rust bloom at every scratch and weld within a few years, while hot-dip galvanized steel with stainless fixings holds up for decades. The problem is most older gates in this city were painted, not galvanized, so we often weld and then re-spec the repaired sections with galvanized stock. If you are deciding between repairing or replacing a gate near Sunset Boulevard, we will tell you which option actually makes sense for our conditions.
Call Gatewood Fence & Gate for Gate Repair in West Hollywood
Hal Gatewood started this shop in 2001, and he still runs it himself with his own crew. We answer the phone with a live person every hour of every day. The 90-Day Done Right Promise is stamped on every job. The price we quote is the price you pay. If your gate is down, sagging, or acting up in West Hollywood, call (818) 873-5061 for a free estimate, and we will be straight with you about what it needs and what it does not.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, building and repairing gates across Los Angeles County since 2001.